MOXA NPort 5450 Series

Network Readiness for up to Four Serial Devices

NPort® 5400 device servers can conveniently and transparently connect up to four serial devices to an Ethernet network, allowing you to network your existing serial devices with only basic configuration. Data transmission between the serial and Ethernet interfaces is bi-directional. By using NPort® device servers, you not only protect your current hardware investment, but also allow for future network expansion. You can both centralize the management of your serial devices, and distribute management hosts over the network.

Independent Operation Mode for Each Serial Port

NPort® 5400 device servers can be used to connect different devices for remote data polling or event handling over a TCP/IP network. Each serial port on the NPort® 5400 operates independently to provide maximum versatility. For example, port 1 can operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4 in TCP Client mode.

User-friendly LCD Panel for Easy Installation

An LCD panel is built into the NPort® 5400?s top panel, with four buttons for inputting data, configuration, and selecting the operation mode. The LCD panel displays the server name, serial number, and IP address, and can be used to enter or modify parameters such as IP address, netmask, and gateway. (The LCD panel is not available on wide temperature models.)

Dual DC Power Inputs
NPort® 5400 device servers support dual power sources by providing both a DC terminal block input and a DC power jack input. Providing two types of power input gives users greater flexibility for use with different applications.

Adjustable Termination and Pull High/Low Resistors

The NPort 5400 series provides adjustable termination and pull high/low resistors for RS-485 applications. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals, and the pull high/low resistors may need adjusting to maintain the integrity of the electrical signal. Since no set of resistor values is universally compatible with all environments, the NPort® 5400 has four sets of DIP switches on the bottom panel to set the termination and pull high/low resistor values.

Ethernet Interface

Number of Ports
1

Speed
10/100 Mbps, auto MDI/MDIX

Connector
8-pin RJ45

Magnetic Isolation Protection
1.5 kV built-in


Serial Interface

Number of Ports
4

Serial Standards
NPort 5410: RS-232
NPort 5430/5430I: RS-422/485 (software selectable)
NPort 5450/5450I/5450-T/5450I-T: RS-232/422/485 (software selectable)

Connector
NPort 5410/5450/5450I/5450-T/5450I-T: DB9 male
NPort 5430/5430I: Terminal block

Serial Line Protection
15 kV ESD protection for all signals
2 kV isolation protection (NPort 5430I/5450I/5450I-T)

RS-485 Data Direction Control
ADDC® (automatic data direction control)

Pull High/Low Resistor for RS-485
1 kÙ, 150 kÙ

Terminator for RS-485
120 Ù



Serial Communication Parameters


Data Bits
5, 6, 7, 8

Stop Bits
1, 1.5, 2

Parity
None, Even, Odd, Space, Mark

Flow Control
RTS/CTS and DTR/DSR (RS-232 only), XON/XOFF

Baudrate
50 bps to 921.6 kbps


Serial Signals

RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND

RS-422
Tx+, Tx-, Rx+, Rx-, GND

RS-485-4w
Tx+, Tx-, Rx+, Rx-, GND

RS-485-2w
Data+, Data-, GND


Software

Network Protocols
ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1, HTTP, SMTP, SNTP, Rtelnet, ARP

Configuration Options
Web Console, Telnet Console, Windows Utility

Windows Real COM Drivers
Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded

Fixed TTY Drivers
SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X

Linux Real TTY Drivers
Linux 2.4.x, 2.6.x, 3.x


Mini Screen with Push Buttons (for standard temp. models)

LCD Panel
Liquid Crystal Display on the case

Push Buttons
Four push buttons for convenient on-site configuration


Physical Characteristics

Housing
Metal

Weight
740 g

Dimensions
Without mounting kit: 158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)
With mounting kit: 181 x 103 x 33 mm (7.14 x 4.06 x 1.30 in)


Environmental Limits

Operating Temperature
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)

Storage Temperature
-40 to 75°C (-40 to 167°F)

Ambient Relative Humidity
5 to 95% (non-condensing)

Altitude
Up to 2000 m

Note Please contact us if you require products guaranteed to function properly at higher altitudes.


Power Requirements

Input Voltage
12 to 48 VDC

Power Consumption
NPort 5410: 350 mA @ 12 V, 190 mA @ 24 V
NPort 5430: 320 mA @ 12 V, 175 mA @ 24 V
NPort 5430I: 530 mA @ 12 V, 280 mA @ 24 V
NPort 5450/5450-T: 350 mA @ 12 V, 190 mA @ 24 V
NPort 5450I/5450I-T: 554 mA @ 12 V, 294 mA @ 24 V


Standards and Certifications

Safety
UL 60950-1, EN 60950-1

EMC
CE, FCC

EMI
EN 55022 Class A, FCC Part 15 Subpart B Class A

EMS
EN 55024

Marine
DNV (standard temp. models only)

Medical
EN 60601-1-2 Class B, EN 55011 (NPort 5410/5450/5450I only)


Reliability

Alert Tools
Built-in buzzer and RTC (real-time clock)

Automatic Reboot Trigger
Built-in WDT (watchdog timer)

MTBF (mean time between failures)
NPort 5410: 205,153 hrs
NPort 5430: 201,699 hrs
NPort 5430I: 114,540 hrs
NPort 5450/5450I: 206,903 hrs
NPort 5450-T/5450I-T: 206,903 hrs

Ordering
NPort 5410	4-Port RS-232 Serial Device Server
NPort 5430	4-port RS-422/485 device server
NPort 5430I	4-port RS-422/485 device server with 2 KV isolation protection
NPort 5450	4-port RS-232/422/485 device server
NPort 5450-T	4-port RS-232/422/485 device server, -40 to 75°C operating temperature (without LCM)
NPort 5450I	4-port RS-232/422/485 device server with 2 KV isolation protection
NPort 5450I-T	4-port RS-232/422/485 device server with 2KV isolation protection, -40 to 75°C operating temperature (without LCM