MOXA ioLogik 2542-HSPA
Product is End of Life : 2023-11-24
Smart HSPA remote I/O with Click&Go Plus, 4 AIs, and 12 DIOs
- Supports cellular (HSPA), Ethernet, and serial communication
- New Click&Go Plus logic provides powerful front-end intelligence
- 4-port unmanaged switch built in for linking to Ethernet devices
- Optimized I/O expansion port for daisy chaining up to 8 ioLogik E1200 units
- 2 serial ports (RS-232/422/485) for connecting field devices
- Built-in datalogger supports an FTP server and microSD? card with up to a 32 GB
- Transforms Modbus RTU into Modbus TCP or Active Tags
- Active communication with patented MX-AOPC UA Server
- Smart alarm management: Email, SNMP traps, TCP, UDP
- Wide operating temperature: -30 to 70°C (-22 to 158°F)
The ioLogik 2500 is a smart remote I/O product with unique hardware and software designs, making it an ideal solution for a variety of industrial data acquisition applications. The ioLogik 2500?s hardware design includes a 4-port unmanaged Ethernet switch and 2 serial ports, enabling the ioLogik 2500 to seamlessly connect to a variety of field devices. One of the Ethernet ports can be used to link to 8 daisy-chained ioLogik E1200 expansion modules to provide more than 100 channels. The ioLogik 2500 acts as the ?head? unit, with Click&Go Plus logic used to control the entire I/O array. Most importantly, the ioLogik 2500?s single IP is all that?s required to connect the entire I/O array to your network, providing the perfect solution for industrial field sites that have an insufficient number of IP addresses.
Powerful Control Logic from the New Click&Go Plus?
The new Click&Go Plus? control logic now supports up to 48 rules with further upgrades to 8 conditions/actions. In addition, its graphical user interface provides 3 logic gates and 3 multi-layers, helping you build more powerful and efficient IO solutions. Once you finish setting up your Click&Go Plus? logic rules, IOxpress?s easy-to-use simulation function can be used to find potential errors in your Click&Go Plus? rules before uploading them to your online devices.
Peer-to-peer (P2P) mode is widely used for industrial applications. Traditionally, you would need to use P2P devices on both sides of the connection. However, if a configuration mismatch occurred between the P2P devices, the P2P connection would fail, after which you would need to spend extra time and effort to check the P2P settings. With IOxpress, all you need to do is set up the output device, and the P2P connection will be established automatically.
One IP for Multiple Expansion I/Os Gives You a Smarter Data Acquisition Solution
The ioLogik 2500?s unique IO expansion hardware design lets you link up to 8 ioLogik E1200 modules into a versatile I/O array with 100+ different I/O channels. The ioLogik 2500 acts as the perfect ?head? unit, using Click&Go Plus logic to control the entire I/O array, and providing a single IP to connect the entire I/O array to your network.
VPN?Build a Reliable and Secure Cellular Communication Network
For security purposes, the ioLogik 2500-GPRS/HSPA also supports IPSec for building a secure VPN tunnel to the host station. With the help of VPNs, cellular devices acting as a VPN client can initiate a connection with a VPN server. Once the connection is established, cellular devices can communicate with other network devices on the same private network.
Powerful Datalogger and Value-added MODBUS Gateway
The ioLogik 2500 supports micro SD cards with up to 32 GB of memory, turning the ioLogik into a powerful datalogger for storing valuable data. And with a built-in FTP server, important data from field sites can be accessed remotely by different systems. In addition, the 2 serial communication ports can be used to input data from devices using the Modbus RTU protocol, and then transform the data into Modbus TCP or AOPC tag format before sending it out over the Ethernet network.
New MX-AOPC UA Server Efficiently Reduces System Response Time
The new MX-AOPC UA supports both UA server and DA server types. MX-AOPC UA server has a number of strengths. UA server provides a standard, state of the art security model, assuring your system?s security, and supports communication channels via the standard UA TCP port. This means that messages can be relayed through third party proxies. In addition, configuring the firewall is be easier, since you won?t need to worry about DCOM settings.
In addition, MX-AOPC supports both the traditional Modbus protocol and Moxa?s patented Push type communication. Unlike the traditional passive ?pull? method, ?active? messages are automatically ?pushed? from the ioLogik 2500 to the SCADA system when the I/O state changes or pre-configured events occur. In this way, information can be accurately and efficiently pushed to the SCADA system as it becomes available.
Powerful Control Logic from the New Click&Go Plus?
The new Click&Go Plus? control logic now supports up to 48 rules with further upgrades to 8 conditions/actions. In addition, its graphical user interface provides 3 logic gates and 3 multi-layers, helping you build more powerful and efficient IO solutions. Once you finish setting up your Click&Go Plus? logic rules, IOxpress?s easy-to-use simulation function can be used to find potential errors in your Click&Go Plus? rules before uploading them to your online devices.
Peer-to-peer (P2P) mode is widely used for industrial applications. Traditionally, you would need to use P2P devices on both sides of the connection. However, if a configuration mismatch occurred between the P2P devices, the P2P connection would fail, after which you would need to spend extra time and effort to check the P2P settings. With IOxpress, all you need to do is set up the output device, and the P2P connection will be established automatically.
One IP for Multiple Expansion I/Os Gives You a Smarter Data Acquisition Solution
The ioLogik 2500?s unique IO expansion hardware design lets you link up to 8 ioLogik E1200 modules into a versatile I/O array with 100+ different I/O channels. The ioLogik 2500 acts as the perfect ?head? unit, using Click&Go Plus logic to control the entire I/O array, and providing a single IP to connect the entire I/O array to your network.
VPN?Build a Reliable and Secure Cellular Communication Network
For security purposes, the ioLogik 2500-GPRS/HSPA also supports IPSec for building a secure VPN tunnel to the host station. With the help of VPNs, cellular devices acting as a VPN client can initiate a connection with a VPN server. Once the connection is established, cellular devices can communicate with other network devices on the same private network.
Powerful Datalogger and Value-added MODBUS Gateway
The ioLogik 2500 supports micro SD cards with up to 32 GB of memory, turning the ioLogik into a powerful datalogger for storing valuable data. And with a built-in FTP server, important data from field sites can be accessed remotely by different systems. In addition, the 2 serial communication ports can be used to input data from devices using the Modbus RTU protocol, and then transform the data into Modbus TCP or AOPC tag format before sending it out over the Ethernet network.
New MX-AOPC UA Server Efficiently Reduces System Response Time
The new MX-AOPC UA supports both UA server and DA server types. MX-AOPC UA server has a number of strengths. UA server provides a standard, state of the art security model, assuring your system?s security, and supports communication channels via the standard UA TCP port. This means that messages can be relayed through third party proxies. In addition, configuring the firewall is be easier, since you won?t need to worry about DCOM settings.
In addition, MX-AOPC supports both the traditional Modbus protocol and Moxa?s patented Push type communication. Unlike the traditional passive ?pull? method, ?active? messages are automatically ?pushed? from the ioLogik 2500 to the SCADA system when the I/O state changes or pre-configured events occur. In this way, information can be accurately and efficiently pushed to the SCADA system as it becomes available.
ioLogik 2542 Specifications
Inputs and Outputs
Analog Inputs 4 channels
Configurable DI/Os 12 channels
Isolation 3k VDC or 2k Vrms
Analog Input
Type Differential input
Resolution 16 bits
I/O Mode Voltage / Current (software selectable)
Input Range ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA (with burn-out detection)
Accuracy
Sampling Rate
Input Impedance > 1M ohms (min.)
Built-in Resistor for Current Input 120 ohms
Digital Input
Sensor Type Wet Contact (NPN or PNP) and Dry Contact
Input Leakage Current < 1 mA (@ 30 VDC)
I/O Mode DI or Event Counter
Dry Contact
Common Type 6 points per COM
Counter Frequency 2.5 kHz
Digital Filtering Time Interval Software configurable
Digital Output
Type Sink
I/O Mode DO or Pulse Output
Pulse Output Frequency 5 kHz
Over-voltage Protection 45 VDC
Over-current Protection 1.5 A per channel @ 25°C
Over-temperature Shutdown 175°C (min.)
Current Rating 500 mA per channel @ 25°C
Common Specifications
WLAN Interface
Standards
Spread Spectrum and Modulation (typical)
Operating Channels (central frequency)
Security
Transmission Rates
TX Transmit Power
RX Sensitivity
LAN
Ethernet
Note The optimized daisy-chain port is not supported on wind industry devices (ioLogik E1261W-T, E1261H-T, or E1263H-T).
Protection 1.5 kV magnetic isolation
Protocols Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP
Serial Communication
Serial Ports 2, RJ45, 3-in-1 interface
Protocols Modbus/RTU (master), serial tunnel mode (client/server)
Serial Line Protection ≥ 8 kV ESD for all signals
Baudrate 1200 to 115200 bps
Serial Communication Parameters
Parity None, Odd, Even
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Flow Control None, RTS/CTS
Baudrate 1200 to 115200 bps
Protocol Modbus/RTU
Power Requirements
Power Input 24 VDC nominal, 9 to 48 VDC
Power Consumption
Physical Characteristics
Wiring I/O cable max. 14 AWG
Mounting DIN rail, wall
Storage
Expansion Slot Up to 32 GB microSD? memory card (SDHC compatible)
Note For units operating in extreme temperatures, industrial grade, wide-temperature SD cards are required.
Environmental Limits
Operating Temperature
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude Up to 2000 m
Note Please contact us if you require products guaranteed to function properly at higher altitudes.
Standards and Certifications
Safety UL 508, EN 60950-1, NCC
EMI EN 55022; EN 61000-3-2; EN 61000-3-3; FCC Part 15, Subpart B, Class A
EMS EN 55024, EN 61000-4-2, EN 61000-4-3,EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11, EN 61000-6-2
Radio FCC Part 22H, FCC Part 24E,EN 301 489-1, EN 301 489-7, EN 301 511
Shock IEC 60068-2-27
Freefall IEC 60068-2-32
Vibration IEC 60068-2-6
Green Product RoHS, CRoHS, WEEE
Inputs and Outputs
Analog Inputs 4 channels
Configurable DI/Os 12 channels
Isolation 3k VDC or 2k Vrms
Analog Input
Type Differential input
Resolution 16 bits
I/O Mode Voltage / Current (software selectable)
Input Range ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA (with burn-out detection)
Accuracy
- ±0.1% FSR @ 25°C
- ±0.3% FSR @ -10 and 60°C
- ±0.5% FSR @ -30 and 70°C
Sampling Rate
- All channels: 400 samples/sec
- Per channel: 100 samples/sec
Input Impedance > 1M ohms (min.)
Built-in Resistor for Current Input 120 ohms
Digital Input
Sensor Type Wet Contact (NPN or PNP) and Dry Contact
Input Leakage Current < 1 mA (@ 30 VDC)
I/O Mode DI or Event Counter
Dry Contact
- On: short to GND
- Off: open
- On: 10 to 30 VDC
- Off: 0 to 3 VDC
Common Type 6 points per COM
Counter Frequency 2.5 kHz
Digital Filtering Time Interval Software configurable
Digital Output
Type Sink
I/O Mode DO or Pulse Output
Pulse Output Frequency 5 kHz
Over-voltage Protection 45 VDC
Over-current Protection 1.5 A per channel @ 25°C
Over-temperature Shutdown 175°C (min.)
Current Rating 500 mA per channel @ 25°C
Common Specifications
WLAN Interface
Standards
- IEEE 802.11a/b/g for wireless LAN
- IEEE 802.11i for wireless security
Spread Spectrum and Modulation (typical)
- DSSS with DBPSK, DQPSK, CCK
- OFDM with BPSK, QPSK, 16QAM, 64QAM
- 802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, DBPSK @ 11 Mbps
- 802.11a/g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mb
Operating Channels (central frequency)
- US: 2.412 to 2.462 GHz (11 channels), 5.18 to 5.24 GHz (4 channels)
- EU: 2.412 to 2.472 GHz (13 channels), 5.18 to 5.24 GHz (4 channels)
Security
- 64-bit and 128-bit WEP encryption
- Full WPA/WPA2 Personal
Transmission Rates
- 802.11b: 1, 2, 5.5, 11 Mbps
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps
TX Transmit Power
- 802.11b: Typ. 18± 1.5 dBm @ 1 to 11 Mbps
- 802.11g: Typ. 18± 1.5 dBm @ 6 to 24 Mbps, Typ. 17± 1.5 dBm @ 36 Mbps, Typ. 16± 1.5 dBm @ 48 Mbps, Typ. 16± 1.5 dBm @ 54 Mbps
- 802.11a: Typ. 18± 1.5 dBm @ 6 to 24 Mbps, Typ. 16± 1.5 dBm @ 36 M
RX Sensitivity
- 802.11b: -97 dBm @ 1 Mbps, -94 dBm @ 2 Mbps, -92 dBm @ 5.5 Mbps, -90 dBm @ 11 Mbps
- 802.11g: -88 dBm @ 6 to 24 Mbps, -85 dBm @ 36 Mbps, -75 dBm @ 48 Mbps, -70 dBm @ 54 Mbps
- 802.11a: -88 dBm @ 6 to 24 Mbps, -85 dBm @ 36 Mbps, -75 dBm @
LAN
Ethernet
- 4 switched 10/100 Mbps RJ45 ports
- 1 optimized port for faster downstream communications with daisy-chained ioLogik E1200 units
Note The optimized daisy-chain port is not supported on wind industry devices (ioLogik E1261W-T, E1261H-T, or E1263H-T).
Protection 1.5 kV magnetic isolation
Protocols Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP
Serial Communication
Serial Ports 2, RJ45, 3-in-1 interface
Protocols Modbus/RTU (master), serial tunnel mode (client/server)
Serial Line Protection ≥ 8 kV ESD for all signals
Baudrate 1200 to 115200 bps
Serial Communication Parameters
Parity None, Odd, Even
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Flow Control None, RTS/CTS
Baudrate 1200 to 115200 bps
Protocol Modbus/RTU
Power Requirements
Power Input 24 VDC nominal, 9 to 48 VDC
Power Consumption
- ioLogik 2512-GPRS: 420 mA @ 24 VDC
- ioLogik 2512-HSPA: 460 mA @ 24 VDC
- ioLogik 2542-GPRS: 500 mA @ 24 VDC
- ioLogik 2542-HSPA: 540 mA @ 24 VDC
Physical Characteristics
Wiring I/O cable max. 14 AWG
Mounting DIN rail, wall
Storage
Expansion Slot Up to 32 GB microSD? memory card (SDHC compatible)
Note For units operating in extreme temperatures, industrial grade, wide-temperature SD cards are required.
Environmental Limits
Operating Temperature
- Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models:
ioLogik 2500-GPRS/HSPA: -30 to 70°C (-22 to 158°F)
ioLogik 2500: -40 to 75°C (-40 to 167°F)
ioLogik 2500-WL1: -30 to 70°C (-22 to 158°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude Up to 2000 m
Note Please contact us if you require products guaranteed to function properly at higher altitudes.
Standards and Certifications
Safety UL 508, EN 60950-1, NCC
EMI EN 55022; EN 61000-3-2; EN 61000-3-3; FCC Part 15, Subpart B, Class A
EMS EN 55024, EN 61000-4-2, EN 61000-4-3,EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11, EN 61000-6-2
Radio FCC Part 22H, FCC Part 24E,EN 301 489-1, EN 301 489-7, EN 301 511
Shock IEC 60068-2-27
Freefall IEC 60068-2-32
Vibration IEC 60068-2-6
Green Product RoHS, CRoHS, WEEE
Los clientes que han visto este artículo también vieron